Engineered to offer the rider a rugged and efficient accessory to pull out the dirt bike when stuck in between rocks, loose sand, fesh-fesh or any other terrain. With the Lift Strap Kit, you’ll be able to rapidly pull out the dirt bike and get back on track.
Husqvarna 2017-2019 Lift Strap Kit 2.0
- Lightweight & built to endure.
- Easy & fast installation.
- Installation doesn’t require disassembly of any major parts of the dirt bike.
- 100% Double nylon.
- 100% Abrasion resistant neoprene handle cover.
This part has been specially designed for Husqvarna 2020 - 2023 Off-road/Enduro dirt bikes all 2T & 4T models (250cc to 500cc).
FRONT LIFT STRAP
Use the following Hardware:
- 01 Lift Strap.
- 04 T-Shaped Aluminum Tabs.
- 02 Button Socket Head Cap Bolts (25mm M6 Bolts).
- 02 Button Socket Head Cap Bolts (20mm M4 Bolts).
- 02 Flanged Serrated Nuts (M6).
- 02 Flanged Nuts (M4).
- 04 Zip ties.
Installation Instructions:
1. Loop one side of the strap around the fork (under the triple clamp).
2. Insert one of the 25mm M6 bolts to the T-shaped aluminum tab.
3. Insert the 25mm M6 bolt with the T-shaped aluminum tab into the big hole of the strap (from the outside part of the strap).
4. Insert the bolt through the second hole (big hole in the tip of the strap).
5. Insert the second tab and then secure the M6 flanged serrated nut (loosely).
6. Insert the 20mm M4 bolt to the T-shaped aluminum tab and pass it all the way through.
7. Secure the M4 flanged nut (loosely).
8. Loop a zip tie around the fork on the upper part of the triple clamp.
9. Insert a 2nd zip tie from under the strap and loop it to the 1st zip tie.
10. Adjust both zip ties and then fix the bolts & nuts firmly.
11. Repeat the installation process on the other side.
Installation Tips:
- Take a look at the pictures to help you understand how you should place correctly the bolts, nuts, tabs and zip ties.
- Prioritize the Brake Cable Side: Begin with the brake cable side first. Completing this side initially creates more working room, making the subsequent side easier to manage.
- Utilize Lower Strap Positioning for Easier Assembly: To facilitate a smoother installation, start by positioning the strap lower on the fork since it narrows as you go down. Compress the aluminum tabs to allow the bolt to pass through. Assemble all components loosely, just threading the bolts and nuts. Once assembled, slide the strap upward into its final desired position and then securely tighten all fasteners.
- You can add a small drop of Loctite (242 Blue) between the bolts & nuts to keep them always secured.
Notes:
- If your bike has a very soft front suspension, please note these important installation adjustments:
1) Ensure no contact by installing the bolts and nuts in the opposite direction.
2) Slightly rotate the mounts outward. This will move the aluminum tabs further away from the top of the fork guard when the suspension is fully compressed.
- The front lift strap's intended and secure installation point is under the triple clamp as it provides a stable, non-slip attachment and it ensures the strap is at the optimal angle for pulling, enhancing lifting leverage. If you want to run fork guards, keep in mind that they will have to be modified/trimmed.
REAR LIFT STRAP FOR ALL 2017-2019 MODELS EXCEPT 2019 TX/FX MODELS
Use the following Hardware:
- 01 Rear Lift Strap.
- 01 Hex Head Screw (25mm).
- 01 Aluminum Spacer.
- 01 Washer.
- 01 Nut.
Installation Instructions:
1. Drill an M6 hole on the rear plastic fender as shown on the picture.
2. Trim your seat so that the head of the bolt can fit adequately.
3. Insert the lift strap under the sub-frame handles on both sides.
4. Pass the bolt into one aluminum spacer, then through a washer, then through both strap holes (use the 2nd hole on both tips) and finally insert the bolt through the drilled hole of the rear plastic fender.
4. Under the rear plastic fender, insert a washer to the bolt and tighten the nut.
REAR LIFT STRAP FOR 2019 TX & FX MODELS
Use the following Hardware:
- 01 Rear Lift Strap.
- 02 Hex Head Screws (25mm).
- 02 Aluminum Spacers.
- 02 Washers.
Installation Instructions:
1. Insert the bolt to the washer.
2. Insert the bolt to the 3rd hole of the strap (3rd from the tip).
3. Insert the bolt to the aluminum spacer.
4. Tighten the bolt to the dirt bike.
5. Repeat on the other side.
Installation Tips:
- Please take a look at the pictures for correct installation.
- We recommend to add a small drop of Loctite (242 Blue) on the bolts to keep them always secured.
- All sales are final.
- No refunds accepted.
- Exchange Policy: Product returns are only accepted due to manufacturing defects, prior to installation or use of the product.